Polymeric Sand Black 50 lb Bags

Available in 50lb bags

• Pickup at West Jordan Landscape Center

Applications

• Can be used for paver joints up to 2″ thick
• Concrete Paver Joints
• Driveway Joints
• Walkway Joints
• Patio Joints

How to use

Preparation

• 1A. Install pavers using manufacturer’s guidelines for bedding, leveling and installation. Fully clean off debris from the project area.
• 1B. Installations should have a proper drainage layer of sand with a depth of 1″ (2.54 cm). In addition, weep holes need to be added to concrete overlays.
• 1C. If existing project, properly clean out joints before applying polymeric sand and skip to step 3.

Step 2

• 2A. Compact pavers thoroughly using a rubber-plated compactor.
• 2B. If compactor is not rubber-plated, cover pavers with a woven fabric while compacting to help protect paver surface from damage.
• 2C. Pavers must be completely dry before installing polymeric sand. Wait 24 hours after rain.

Application

• 3A. Gently tumble bag, then cut the bottom and apply Pavermate Polymeric Sand evenly over the surface.
• 3B. Spread sand into joints, completely filling to the full depth of the pavers.
• 3C. Avoid pushing sand over long distances.
• 3D. Remove excess sand from surface of pavers before compacting.

Step 4

• A. Compact filled joints using a rubber-plated compactor.
• 4B. Repeat compacting and filling (steps 3A – 4A) if necessary.

Step 5

• 5A. Remove excess sand from paver surface using a soft bristle broom and set the joint height with a leaf blower on idle.
• 5B. Once complete, joint height should be filled to 1/8″ (.32 cm) below the top of the paver.

Activation

Step 6

• 6A. Working in sections up to 200 sq. ft. (18.58 sq. m.), water the section for a total of 2 minutes.
• 6B. Do not allow the section to dry during the 2 minute watering:
• 6C. MIST: Use hose with a sprayer attachment set to “mist” or similar light setting. Mist area until the surface is wet.
• 6D. SHOWER: Next, set hose to “light shower” to allow more water over the area. Repeat shower two times over the section.

Step 7

• 7A. Use a screwdriver to test for proper moisture depth of at least 1″ (2.54 cm). If depth is not achieved, immediately wet the area with a shower setting.
• 7B. Once moisture depth is achieved, blow off excess water using a leaf blower.

Step 8

• 8A. Rain safe 10 minutes after joint activation.
• 8B. A flexible joint is a sign that reaction has occurred but is not completely cured.
• 8C. A dry environment is important to allow joints to fully cure. For best performance, install when no rain is forecasted for 24 hours.
• 8D. Wait 28 days prior to cleaning or sealing.

COVERAGE

• Narrow Joints Typical coverage is 55 – 75 sq. ft. (5.11 – 6.97 sq. m.) per bag.
• Wide Joints Typical coverage is 20 – 30 sq. ft. (1.86 – 2.79 sq. m.) per bag.
• Coverage will vary depending on joint depths and widths. This coverage is for reference only and is not guaranteed.

Notes

• Temperature Requirement Temperatures must remain above 32°F (0°C) throughout installation and curing.
• Wet Areas Not recommended for wet/heavily shaded areas. Do not use on pool copings.
• Curing For best results, wait 28 days after installation before cleaning and sealing.

• Delivery locations should be curbside or in the front driveway only.
• After you place your order, expect a call from our office on the next business day to schedule the delivery.
• Lead times for deliveries vary throughout the year based on current demand. These could vary from a couple days to more than a week. If timing is an issue, please call the office to place the order or check current lead times, or click this link to check our current lead times.
• More information about deliveries.

Your satisfaction is important to us. Please review our Cancellation, Rescheduling, and Return Policy before placing an order online or over the phone.